Board use

板材用途

• U型龍骨吊頂系統

  該系統是安裝大型吊頂的最佳選擇。

  在安裝之前必須先標明固定件的位置 首先，用吊件和吊桿將主龍骨水平地固定在樓底上，主龍骨之間的中心距一般為900-1200mm固定點之間的距離亦為900-1220mm，吊件中的彈簧卡能把主龍骨調節到理想的水平位置，必須保證所有的主龍骨都在同一水平面上，然后再用掛件將副龍骨垂直固定在主龍骨上，副龍骨之間的中心距為610mm。在板材的縱向接縫處，用兩個水平件將橫撐龍骨固定到副龍骨上，橫撐龍骨的中心距為1220mm，當龍骨必須用一個接長件來加長時，龍骨與龍骨之間接駁處必須是交錯排列恒火板在鋪設時板材的長邊方向必須與副龍骨的方向相垂直，并且板材寬度方向的接縫交錯排列。螺釘上在距板邊15mm，距板角50mm的位置上，螺釘之間的中心距為200-300mm。板材不固定在墻體上說明吊頂對周圍的墻體來說是完全獨立的，這種形式吊頂不受墻體變動的影響和牽制。如果在防火、隔熱、隔聲或防塵方面要求較高的場所，應該使龍骨和板材與墻體四邊進行剛性連接，使吊頂與墻體連成一個整體結構。在u型龍骨吊頂系統中，大面積的吊頂必須以伸縮縫進行分隔，每部分最大幅面不得大于60m

• 恒火板隔墻系統

  ■安裝前，根據設計圖紙，必須標好沿頂、沿地龍骨的準確位置，及標明門窗衛生設施及管道位置
  ■安裝龍骨時，豎龍骨應向同一方向依次排布，豎龍骨中心間距為610mm，特別要確保豎龍骨的垂直。
  ■防火等級要求高的墻體，板材應縱向鋪設，而且豎龍骨兩側板材接縫應錯開;
  ■板材之間自然拼接不留縫，但板材與地面間必須留有3mm的縫。固定板的自攻螺釘的中心距為250-300mm，距板邊為15mm，距板角為50mm，釘頭沉入板面1mm